Toonmate Premium Table with Plate Recesses
Item No. 315667
Images
Details
https://www.overtons.com/toonmate-premium-table-with-plate-recesses-315667.html
Toonmate Premium Table with Plate Recesses
Toonmate Premium Table with Plate Recesses is rated
out of
5 by
6.
Item No. 315667
$175.74
$184.99
Additional Information
This durable Toonmate Premium Table is made of UV-protected, weatherproof plastic. Designed for convenience with 3 molded-in cupholders and 3 molded-in 8-5/8" diameter plate recesses, this table comes with the patented Sequoia table leg and mount system. Stainless semi-flush mount base surface mounts to the deck, so there are no holes to cut in the floor. 26" high table legs easily twist-lock into place. Table: 23" diameter.
Show moreShow less
Toonmate Premium Table with Plate Recesses is rated
out of
5 by
6.
Rated 4 out of
5
by
Odis from
Works well
our pontoon was setup for fishing with no table so this works perfect, when not needed easy to take down and store, snap in place when needed. Perfect for what we wanted.
Date published: 2013-06-22
Rated 4 out of
5
by
Jeff from
Exactly what we wanted
We wanted a table for our 21' Sea Ray ski boat that would allow us to entertain on the boat when at anchor. After drilling a few quick screw holes, the base went on easily, and the 'table leg system' works exactly as advertised. Easy to pop in the leg and then pop on the table for use whenever we're hanging out. And it's just as easy to take it apart and store right on the boat. We don't keep it up when cruising as it seems likely that a hard push against it by a learching passenger might damage the base (same as with any such table). But then we got it specifically because it's so easy to pop up/pop down.
Date published: 2012-05-17
Rated 5 out of
5
by
concora 9899 from
Great Design
This table was added to my pontoon as a second dining spot in the front and it is perfect. The round design makes easy passby, yet is large enough to be quite functional. The plate recesses are just the right size for paper plates with snacks, no sliding. The install was ultra simple and solid. The Sequoia system is top notch and reliable to attach and detatch as needed. I wouldn't use any other. The low surface mount is very safe when the table is taken down.
Date published: 2011-06-28
Rated 4 out of
5
by
Lynn Armstrong from
good product
perfect for our pontoon boat
Date published: 2011-06-24
Rated 4 out of
5
by
Lynn Armstrong from
Satisfied with product
Product is fine. [...]
Date published: 2011-06-22
Rated 5 out of
5
by
Lake resident from
great table
great table - sturdy! love the built in cup/plate holders.
Date published: 2010-09-16
What is the depth and diameter of the cup holders?
3 ½” diameter. 2” deep.
Date published: 2017-09-05
Do you sell just the table top only ?
Thank you for your question.
The table is not sold top only.
Date published: 2016-08-18
i want to replace a table on my pontoon. the existing table leg is recessed in to the floor. can i get table model # 76040 which is not in the floor but on top of the floor?
Yes. All you'll need to do is either a) use the same screw holes as the old table base used for the new base, or b) drill new screw holes for the new base. You can simply keep rotating the new base until there are no screw holes in then deck where it requires screw holes and it will be like a new installation. There should be no issue about the big hole in the deck from the old table base since the new one doesn't extend below the surface when installed.
Date published: 2015-09-23