Additional Information
Features
These trailering clips provide an economical way to protect stern drive units while trailering or storing. Trailering clips relieve the stress on the hydraulic tilt and trim system by transferring the stern drive weight from the hydraulic cylinders to the transom bracket. These clips help prevent damage from weight surges during trailering and increase the life of the o-rings, internal seals, and valves in the hydraulic system. Resistant to UV rays, gasoline, oil, and other marine chemicals.
These 12" long clips fit all sterndrives with 3/4" hydraulic rams, including: Mercruiser Alpha I, Alpha I Generation II, Bravo I, Bravo II, Bravo III, and Blackhawk Stern Drives. The clips can also be trimmed to fit shorter rams. Sold in pairs.
Show moreShow less
These 12" long clips fit all sterndrives with 3/4" hydraulic rams, including: Mercruiser Alpha I, Alpha I Generation II, Bravo I, Bravo II, Bravo III, and Blackhawk Stern Drives. The clips can also be trimmed to fit shorter rams. Sold in pairs.
- Protects sterndrive units while trailering
- Reduces strain on hydraulic system
- Easy to install
- Increases life of o-rings, seals, and valves
- Fits all stern drives with 3/4" hydraulic rams
Specs
Unit Weight | 1.15 lb |
---|---|
Brand | T-H Marine Supplies |

WARNING: Cancer and Reproductive Harm
For more information, go to www.P65Warnings.ca.gov/product.
Reviews
Q & A
These trailering clips provide an economical way to protect stern drive units while trailering or storing. Trailering clips relieve the stress on the hydraulic tilt and trim system by transferring the stern drive weight from the hydraulic cylinders to the transom bracket. These clips help prevent damage from weight surges during trailering and increase the life of the o-rings, internal seals, and valves in the hydraulic system. Resistant to UV rays, gasoline, oil, and other marine chemicals.
These 12" long clips fit all sterndrives with 3/4" hydraulic rams, including: Mercruiser Alpha I, Alpha I Generation II, Bravo I, Bravo II, Bravo III, and Blackhawk Stern Drives. The clips can also be trimmed to fit shorter rams. Sold in pairs.
Show moreShow less
These 12" long clips fit all sterndrives with 3/4" hydraulic rams, including: Mercruiser Alpha I, Alpha I Generation II, Bravo I, Bravo II, Bravo III, and Blackhawk Stern Drives. The clips can also be trimmed to fit shorter rams. Sold in pairs.
- Protects sterndrive units while trailering
- Reduces strain on hydraulic system
- Easy to install
- Increases life of o-rings, seals, and valves
- Fits all stern drives with 3/4" hydraulic rams
Unit Weight | 1.15 lb |
---|---|
Brand | T-H Marine Supplies |

WARNING: Cancer and Reproductive Harm
For more information, go to www.P65Warnings.ca.gov/product.
Rated 5 out of
5
by
Drew from
Bravo3
Simple to cut and install. Trailed my boat with a Bravo 3 from New York to Tampa and it never faltered.
Date published: 2020-11-25
Rated 3 out of
5
by
Cyndi from
Okay
They arrived quickly but one would never slide over the rod no matter which side we tried it on. When you did get it on it was almost impossible to remove, at times we even wondered if we were going to be able to get it back off. We just use one, it keeps the motor from drifting down.
Date published: 2020-08-30
Rated 5 out of
5
by
Stuart from
Great product
Work great and these work on a omc outdrive just has to cut them down.
Date published: 2020-07-27
Rated 5 out of
5
by
robert from
trailering clips
these clips work great need to have for your boat .
Date published: 2020-05-28
Rated 3 out of
5
by
Paul from
Work well, require some trimming though
Didn’t realize they need to be cut, but was simple
Date published: 2019-08-16
Rated 5 out of
5
by
Mac67 from
Excellent support
Used to have a Hook, These work great and do not fall off!
Date published: 2016-10-24
Rated 5 out of
5
by
Gary from
Excellent product, 5 mins to trim to length install.
Took 5 mins. to trim and add a cord works great.
Date published: 2015-08-22
Rated 5 out of
5
by
motox from
Works Good
Made of good material. I had to cut them for length. I also drilled two holes on one end to secure them with zip ties. Probably don't need the zip ties because they fit snug on the cylinder ram. I also lower the drive an 1/8" on the ram to keep them held tight in place. These are very nice trailing clips and I am very happy with them.
Date published: 2015-07-23
would these work on a mercury 4 stroke 75 horse tiller?
Please contact our Technical Team at 1-800-334-6541, with additional information.
Date published: 2017-08-18
Will these fit volvo penta sx cobra drves?
Yes, as long as the hydraulic rams are 3/4".
Date published: 2017-06-06
Will these fit the mercury Alpha One stern drive?
Yes, these Trailering Clips will fit the Alpha I.
Date published: 2016-12-12
Anyone know the cut sizes on the instruction sheet? Mine got thrown away by accident. I have the alpha 1 with anodes. Thanks
The Sterndrive Trailering Clips for a Mercruiser Alpha I will need to be cut down to 9-1/2".
Date published: 2016-06-03
Are these a set or only one?
These are a set. 2 clips per pack.
Date published: 2019-08-18
What is the length?
Hello Geno, The Trailering Clips are 12" in length. Thank you, Steve
Date published: 2015-09-23
does it replace or do you use with transom saver
Visit the supplier's advertisement as well for more information about these trailering clips at http://www.thmarine.com/product057e.html?PRID=123
Date published: 2015-09-23