Overton's Indoor/Outdoor Do-It-Yourself Carpet Adhesive gallon
Item No. 314725
Overton's Indoor/Outdoor Do-It-Yourself Carpet Adhesive gallon is rated
out of
5 by
91.
Images
Details
https://www.overtons.com/overtons-indooroutdoor-do-it-yourself-carpet-adhesive-gallon-314725.html
Overton's Indoor/Outdoor Do-It-Yourself Carpet Adhesive gallon
$37.99
$39.99
Save $2.00
(
5% Off
)
Additional Information
Features
Use on fiberglass aluminum and marine-grade plywood only. This adhesive will not work on pressure-treated wood. One gallon covers up to 125 square feet. Shipped ground only.
Show moreShow less
Features:
- Easy-to-use water-resistant
- Formulated for use with outdoor carpet
- Use on marine-grade plywood fiberglass aluminum
- Covers up to 125 square feet
Specs
| Unit Weight | 9.26 lb |
|---|---|
| Brand | Overton's |
Reviews
Q & A
Use on fiberglass aluminum and marine-grade plywood only. This adhesive will not work on pressure-treated wood. One gallon covers up to 125 square feet. Shipped ground only.
Show moreShow less
Features:
- Easy-to-use water-resistant
- Formulated for use with outdoor carpet
- Use on marine-grade plywood fiberglass aluminum
- Covers up to 125 square feet
| Unit Weight | 9.26 lb |
|---|---|
| Brand | Overton's |
Rated 1 out of
5
by
Bob from
Disappointed
Product did not come with application instruction, as far as "allow to properly tack before applying carpet". What does that mean? Also I used a 3/16 Trowel to apply per instructions and this product does not cover the amount it says it does. Very disappointed!!!
Date published: 2021-05-24
Rated 4 out of
5
by
Steve from Michigan from
Speads easily
Product goes on very thin. It was easy to spread and appears to work well.
Date published: 2021-05-24
Rated 1 out of
5
by
Aaron from
Very runny
GLue is very runny, not good for vertical boat surfaces. Just put some pieces togather, will see how well it holds. I don't see how it will make the coverage it claims.
Date published: 2020-02-04
Rated 5 out of
5
by
Mark Netro from
Overtons carpet adheasive
Great item, worked great, thanks. Will use again too
Date published: 2019-10-23
Rated 1 out of
5
by
BassMaster from
This glue is garbage.
Followed the directions to a T, waited 2 weeks and went fishing today. It rained and guess what? The glue re-hydrated itself and the carpet came loose all over the entire floor. Over $350.00 of 20 oz marine carpet ruined not to mention the price of the glue and labor.
Date published: 2017-07-12
Rated 5 out of
5
by
sparky from
good product
Haven't used this product yet still waiting on correct carpet to ship. I did have some left over i use a couple of weeks back on a different boat and it work great.
Date published: 2013-09-12
Rated 5 out of
5
by
Mastercraft Rob from
great product
Great product went on easy. Do not use to much and let it setup a little bit before laying the carpet down
Date published: 2013-09-11
Rated 5 out of
5
by
ski from
Excellent product. Workd as advertised.
Used on pontoon boat deck. Product worked as advertised. Easy clean up.
Date published: 2013-08-09
Can this glue be applied to plywood that has been primed and painted with an exterior latex paint?
Thank you for your question.
The answer would be No.
With the latex paint on the plywood currently--the bond between the glue and the wood is only as strong as the latex bond is to the wood. Instructions for glue use is located online at http://www.overtons.com/assets/prodman/35918.pdf
Date published: 2017-02-06
I used this glue, put it down in weather over 65 degs but it has been dipping down to the mid 40s the past two days, should I wait longer or be worried about anything. I saw it stated above 65, but figure its mainly for a quicker dry time.
Thank you for your question.
The cold weather will slow your cure time. If at all possible--pull the boat outside and let the sun help increase the temp of the carpet/adhesive combo for full cure.
Date published: 2016-10-12
will this work on vinyl carpet?
Thank you for your question. As long as the carpet has a rubber backing--should work for your application.
Date published: 2015-09-23
If applying to plywood in a 72 degree environment, roughly how long to allow to tack up before applying carpeting.
Thank you for your question. No tack time needed – the average do-it-yourself person most likely may wait to long to allow it to tack (like you would with contact cement) Since this adhesive is water-based, you can simply apply carpet to the wet adhesive, smooth out any wrinkles, and let it cure in a dry environment for 24-48 hours (check edge to make sure completely cured before exposing to the elements). I hope this is helpful.
Date published: 2015-09-23
will this product adhere to BB Plyform plywood
It is only meant to be applied to marine grade plywood, not pressure treated plywood, because with pressure treated, the copper salts will leach out and disolve the adhesive and the rubber carpet backing.
Date published: 2015-09-23
will this adhere to plastic plywood?
The adhesive is water based, but unfortunately, there are so many different types of plastic, it is very hard to determine if it would work. If you would like to call in to our tech department at 1-888-683-7866, we would be happy to discuss this.
Date published: 2015-09-23
would it not adhere to pressure treated plywood?
No it does not. The chemicals in the treated plywood don't allow for a good bond.
Date published: 2015-09-23
HOW DO YOU PUT IT DOWN?
This is usually applied with a trowel which we sell separate (item 35973)
Date published: 2015-09-23