Boss MR1002 Riot 200-Watt Two-Channel Amplifier

Item #: 321877
4.7 out of 5 Customer Rating
Save $12.08 (30% Off)
Additional Freight charge of null applies

Boss MR1002 Riot 200-Watt Two-Channel Amplifier
Boss MR1002 Riot 200-Watt Two-Channel Amplifier
Save $12.08 (30% Off)
Ship to Home
Delivery time calculated in checkout Delivery calculated in checkout
Order Pickup
Not Available

FREE Standard Shipping over $99.

Good Sam Members: FREE Shipping over $49

This item is excluded from all discounts and promotions.

  • This item is currently not available
Minimum order quantity of 1
Maximum order quantity of 100
The Boss MR1002 Riot Full Range, Class A/B Amplifier is known for its great sound quality and efficient power output. Weather-proof to stand up to the marine environment, this amp features high and low level inputs, variable gain control, and thermal/overload/short protection. 2 ohm stable impedance. 200-Watt Two-Channel Amplifier: 75W x 2 RMS @ 2 ohm; 38W x 2 RMS @ 4 ohm. 5.25"L x 9"W x 2"H.


2 Ohm Stable
The lowest impedance accepted by this amplifier is 2 ohms. Amplifiers that are 2 ohms stable produce more power resulting in more volume. This amp can comfortably power speakers or subwoofers with all channels being used at a load of 2 ohms.

Class A/B
Class A/B amplifiers have long been known for their ability to produce great quality sound while performing more efficiently than pure Class A amplifiers. Specific linear circuitry further reduces distortion while increasing both sound quality and power output.

Fully Marinized
Utilizes integrated high-tech, state-of-the-art waterproofing materials plus special UV coatings for plastic surfaces, coated circuit boards, and connections to protect against harsh outdoor elements and resist corrosion.

High and Low Level Inputs
An amplifier with both high-level and low-level inputs provides flexibility by allowing you to build an audio system using virtually any standard factory or aftermarket source unit. High-level (speaker level) inputs accept the signal from the speakers, while low-level (RCA) inputs accept the signal from the pre-amp outputs of the source unit.

If the amplifier gets too hot, the thermal protection circuit turns the amp off and allows the amp to cool down before turning it back on. If a speaker fails causing an electrical short, the protection circuit will automatically cut the output and remain in that state until the short is resolved. These safety features give you peace of mind knowing the amplifier is constantly monitoring conditions to protect itself.

Variable Gain Control
Variable Gain Control lets you balance the amps output with the speakers or subs the amp is driving. Too much gain will lead to distortion and too little will lead to clipping.

• Amp Topology: Full Range, Class A/B
• 2-Channel Configuration
• Total Power Output: 200 Watts
• Peak Power @ 2 Ohm: 100 Watts x 2
• Peak Power @ 4 Ohm: 50 Watts x 2
• RMS Power @ 2 Ohm: 75 Watts x 2
• RMS Power @ 4 Ohm: 38 Watts x 2
• Speaker Impedance: 2 to 8 Ohm
• Total Harmonic Distortion: 0.01%
• Channel Separation: ≥ 60 dB
• Signal/Noise Ratio (A Weighted): 90 dB
• Frequency Response: 12 Hz to 22 kHz ± 1 dB
• 5.25"L x 9"W x 2"H
  • Full range, class A/B
  • High and low level inputs
  • Variable gain control
  • Thermal/overload/short protection
  • 2 ohm stable impedance
5.25"L x 9"W x 2"H
2-Channel Amplifier
Remote Control
Waterproof Rating
200.00 W
Unit Weight
2.54 lb
Boss Audio
You May Also Like