Rule 35A Rule-A-Matic Float Switch For Bilge Pump
Item No. 315760
Rule 35A Rule-A-Matic Float Switch For Bilge Pump is rated
out of
5 by
10.
Details
https://www.overtons.com/rule-35a-rule-a-matic-float-switch-for-bilge-pump-315760.html
Rule 35A Rule-A-Matic Float Switch For Bilge Pump
$28.49
$29.99
Compare at $39.99
Save $1.50
(
5% Off
)
Additional Information
Features
Rule's 35A float switch for bilge pumps features abrasion-resistant marine-grade blocked wire. Switch is constructed with exclusive moisture-tight seals and an environmentally friendly mercury-free design. Suitable for any submersible bilge pump with an operating current rating of 14 amps at 12V DC. Switch will turn pump on when the water level reaches 2" and will turn the pump off when the level falls to 3/4". 16-gauge wire size. 1-3/4" x 2-5/8". Two-year warranty.
Show moreShow less
- Abrasion-resistant blocked wire
- Moisture-tight seals
- Mercury-free design
- 14-amp maximum operating current
Specs
Amps @ 12v | 14.00 A |
---|---|
Dimensions | 1-3/4" x 2-5/8" |
Manufacturer Warranty | 2 Year |
Unit Weight | 0.36 lb |
Brand | Rule |

WARNING: This product can expose you to CHEMICALS-C, a chemical known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov/product.
Reviews
Q & A
Rule's 35A float switch for bilge pumps features abrasion-resistant marine-grade blocked wire. Switch is constructed with exclusive moisture-tight seals and an environmentally friendly mercury-free design. Suitable for any submersible bilge pump with an operating current rating of 14 amps at 12V DC. Switch will turn pump on when the water level reaches 2" and will turn the pump off when the level falls to 3/4". 16-gauge wire size. 1-3/4" x 2-5/8". Two-year warranty.
Show moreShow less
- Abrasion-resistant blocked wire
- Moisture-tight seals
- Mercury-free design
- 14-amp maximum operating current
Amps @ 12v | 14.00 A |
---|---|
Dimensions | 1-3/4" x 2-5/8" |
Manufacturer Warranty | 2 Year |
Unit Weight | 0.36 lb |
Brand | Rule |

WARNING: This product can expose you to CHEMICALS-C, a chemical known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov/product.
Rated 5 out of
5
by
none from
Easy to install
Easy to install and works great..
Date published: 2015-04-03
Rated 2 out of
5
by
FiveC's from
Don;t buy it
I've used this switch a couple times but now more. It hangs. Pump does not go on. Just cleaned the cabin bilge with 6 inches of water in rear cabin. Never again.
Date published: 2012-07-28
Rated 4 out of
5
by
beernutz from
Float Switch
Easy to install
Date published: 2011-09-13
Rated 5 out of
5
by
E K from
very good product
Installed it in my 25 ft cruiser..its easy to install and turns on and like it should
Date published: 2011-06-22
Rated 4 out of
5
by
Tony from
works fine
make sure it is wired properly if being used as an automatic bilge pump start and stop.
Date published: 2011-06-15
Rated 5 out of
5
by
Mike from
Very Dependable Switch
Good no worry auto bilge switch. This the second one I have purchased
Date published: 2010-08-03
Rated 5 out of
5
by
Bob from
Does what it says it will do!
Just installed it. It was simple to install and worked well with the first rainfall.
Date published: 2010-04-22
Rated 4 out of
5
by
wakeboard crazy from
It works
I have only had it a week installed on my boat. Went on a house boat trip where my boat sat in the water and the switch turned on my bildge pump as it should. Not had it long enough to test it's durability.
Date published: 2009-07-22
how long are the wires on this switch?
Hello Jack, The length of the wires are 29" long. Thank you, Steve
Date published: 2017-06-16
can this float be used with any bilge?
It is universal up to 14 amps.
Date published: 2017-06-16
can i hook this up to my old pump and if so will it work off my stock switch
You can hook this up to your old pump and run it off the stock switch.
Date published: 2017-06-16