Prop Nut Kit - Evinrude/Johnson V6, V4, V8; OMC Stern Drives and Seadrive
Item No. 314210
Images
Prop Nut Kit - Evinrude/Johnson V6, V4, V8; OMC Stern Drives and Seadrive
Details

Prop Nut Kit - Evinrude/Johnson V6, V4, V8; OMC Stern Drives and Seadrive

Prop Nut Kit - Evinrude/Johnson V6, V4, V8; OMC Stern Drives and Seadrive is rated 4.2 out of 5 by 6.
  • y_2019, m_2, d_18, h_23
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.11
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_314210, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_overtons
  • bvseo_sdk, dw_cartridge, 17.1.0, p_sdk_3.2.0
  • CLOUD, getAggregateRating, 816ms
  • reviews, product
Item No. 314210
$21.84 $22.99
Product Actions

In Stock

Additional Information
Worn or scored thrust washers and prop nuts can cause damage to your prop shaft and propeller face. Protect your drive system by changing your thrust washer and prop nut when replacing or inspecting your propeller.

For use with Evinrude/Johnson: V-6s; '85 120, 140 V-4s; V-8s '85 and later; 2.5 and 2.6 liter Seadrives; OMC sterndrives: V-6s and small block V-8s.
Show moreShow less
  • For use with Evinrude/Johnson: V-6;
  • '85 120, 140 V-4; V-8 '85 or later;
  • OMC Stern Drives: V-6 and small block V-8;
  • Seadrives: 2.5 and 2.6 Liter
  • Prop Nut Kit - Evinrude/Johnson V6, V4, V8; OMC Stern Drives and Seadrive is rated 4.2 out of 5 by 6.
    Rated 2 out of 5 by from Not as described. return was painless. Prop nut kit did not match photo, and did not fit the outboard claimed. The part number was correct. The return was painless. I have not yet received the refund, but have received an email telling me it's being processed.
    Date published: 2014-08-05
    Rated 5 out of 5 by from Highly recommend for replacement Glad I added this to my prop replacement.
    Date published: 2011-12-21
    Rated 4 out of 5 by from works, but pricey I would have save 50% if i went to a marina, the you still need to buy a $30 thrust washer, But quility is good, use coupons
    Date published: 2011-07-13
    Rated 5 out of 5 by from Extra protection Carefully, and with all engine power disengaged, place a block of wood between the propeller blade and motor shaft to secure the prop from turning while loosening the nut. Remove cotter pin with a pliers, then remove the old nut with a prop wrench. Slide off the prop...next remove the thrust washer behind it. Before the prop is to be re-installed, check motor shaft's spline for damage and wear. Clean the spline completely, then re-grease spline liberally with new marine lube. Replace new thrust washer first, and then aligne prop spline carefully ...push prop on. Use wood block again and prop nut wrench to tighten your new prop nut onto the spline shaft. Place new cotter pin through the nut hole and bend pin with a pliers to secure it. Check condition at least twice every season for any wear.
    Date published: 2010-11-24
    Rated 5 out of 5 by from Great value pack Great product good value
    Date published: 2010-05-26
    Rated 4 out of 5 by from it works works and fits like it should
    Date published: 2010-04-23
    • y_2019, m_2, d_18, h_23
    • bvseo_bulk, prod_bvrr, vn_bulk_2.0.11
    • cp_1, bvpage1
    • co_hasreviews, tv_0, tr_6
    • loc_en_US, sid_314210, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_overtons
    • bvseo_sdk, dw_cartridge, 17.1.0, p_sdk_3.2.0
    • CLOUD, getContent, 41ms
    • reviews, product

    Need instructions how it goes together the one i have on rite now is different thanks bill 

    Asked by: The king
    The forward thrust washer goes on first (The larger round gold one). The prop nut is the last piece you put on.
    Answered by: Product Specialist
    Date published: 2017-07-19

    Is this the Prop Nut Kit I need for a 1999 Johnson, 175 horse on an original Raker Prop?

    Asked by: IronBass
    If your engine falls in the above listing then it will work. They go by engine make and model. It should work for you.
    Answered by: Bryant C
    Date published: 2015-09-23

    will this prop nut kit work with a 1999 Volvo SX outdrive? Thanks.

    Asked by: Kyle
    The prop nut kit that you have questioned will not work for a Volvo SX outdrive. Unfortunately we do not have one in stock that would work for the Volvo SX Outdrive but we can special order it for you. If you would like to special order it please contact us here at Overton's at 1-888-OVERTON and any of our Technical Product Specialist will be glad to assist you.
    Answered by: Brooks, Marine Buyer
    Date published: 2017-07-18
    • y_2019, m_2, d_18, h_23CST
    • bvseo_bulk, prod_bvqa, vn_bulk_2.0.11
    • cp_1, bvpage1
    • co_hasquestionsanswers, tq_3
    • loc_en_US, sid_314210, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_overtons
    • bvseo_sdk, dw_cartridge, 17.1.0, p_sdk_3.2.0
    • CLOUD, getContent, 91ms
    • questions, product