Dockmate Universal 3-Way Dock Fender
Item No. 315028
Dockmate Universal 3-Way Dock Fender is rated
out of
5 by
9.
Images
Details
https://www.overtons.com/dockmate-universal-3-way-dock-fender-315028.html
Dockmate Universal 3-Way Dock Fender
$80.99
$89.99
Save $9.00
(
10% Off
)
Additional Information
Features
Versatile fendering that mounts three ways. This affordable dock fendering is made from white, marine-grade, flexible PVC with special UV inhibitors and fungicides. Unaffected by gas, oil, and saltwater, it will not warp, chip, or deteriorate. Unique design allows mounting in many various configurations. 5" max. height. Sold in 20' rolls. Mounting hardware sold separately. Typical installation requires about 4 screws per running foot, mounted 6"-8" apart at top and bottom.
Show moreShow less
- Fendering mounts 3 ways
- White, marine-grade, flexible PVC
- UV inhibitors and fungicides
- 5" max. height
Specs
| Bumper Type | Straight |
|---|---|
| Dimensions | 5"H |
| Unit Weight | 12.50 lb |
| Brand | Dockmate |
WARNING: This product can expose you to chemicals including Titanium Dioxide, Vinyl Chloride, which is [are] known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov/product.
Reviews
Q & A
Versatile fendering that mounts three ways. This affordable dock fendering is made from white, marine-grade, flexible PVC with special UV inhibitors and fungicides. Unaffected by gas, oil, and saltwater, it will not warp, chip, or deteriorate. Unique design allows mounting in many various configurations. 5" max. height. Sold in 20' rolls. Mounting hardware sold separately. Typical installation requires about 4 screws per running foot, mounted 6"-8" apart at top and bottom.
Show moreShow less
- Fendering mounts 3 ways
- White, marine-grade, flexible PVC
- UV inhibitors and fungicides
- 5" max. height
| Bumper Type | Straight |
|---|---|
| Dimensions | 5"H |
| Unit Weight | 12.50 lb |
| Brand | Dockmate |
WARNING: This product can expose you to chemicals including Titanium Dioxide, Vinyl Chloride, which is [are] known to the State of California to cause cancer.
For more information, go to www.P65Warnings.ca.gov/product.
Rated 4 out of
5
by
rooster from
The edging worked perfectly
Iused this edging around my pool. It looke good but was a little tougher to install solo than I had hoped. Two people made it a breeze
Date published: 2010-07-21
Rated 1 out of
5
by
bill from
doesn't do the job.
It is not "3 way." While it may be ok for lighter uses, it definitely cannot replace other products for direct bumping of boat on pier boards. It is too flimsy and thus "3 way" is a mischaracterization of the product.
Date published: 2010-05-31
Rated 3 out of
5
by
kingwoodlee from
Too flimsy
Didn't hold the u-shape as shown in the picture. Also wouldn't lay flat for a nice look once mounted.
Date published: 2010-05-12
Rated 5 out of
5
by
Blair from
Pleased
Very easy to use. It went on my dock with ease. I used a hacksaw to cut to length. Did exactly what i wanted.
Date published: 2010-02-02
Rated 5 out of
5
by
Bob from
Very friendly an accomodating
Good produt to protect my PWC
Date published: 2009-11-24
Rated 5 out of
5
by
Dave from
very satisfied
dock edge
Date published: 2009-07-10
Rated 4 out of
5
by
Ann from
Used at front of "V-shaped" boat slip.
Flexible to fit around corners also.
Date published: 2008-09-30
Rated 5 out of
5
by
Smokey2 from
Can be used four ways!
I needed small boat protection on one side of my dock that was 8 inches in height and 16 feet long. The horizonal mounting did not do a satisfactory job, so I cut 8 inch strips and mounted them vertically 3 inches apart covering the entire 16 feet, plus covered two sharp corners with 8 inch strips. Works great!
Date published: 2008-06-24
What do you recommend on the corners.
Thanks for your question. The corners used will depend on the style dock you have. Our most popular corner is item 73612. It provides excellent coverage and you can cut the 3-way dock bumper to butt up against it. We always recommend extra protection on the corners since they can cause the most damage. If the side profile of your dock is not very tall you can also consider corner 74624 or 34880.
Date published: 2015-09-23
how far apart are the screw holes?
you make your own, however far apart you need them the product does not come with pre-made holes
Date published: 2015-09-23
Length?
This item is sold in 20ft rolls.
Date published: 2015-09-23
how long are these, don't see any sizes
They come in 20' rolls.
Date published: 2015-09-23
WHAT ARE THE DMENSIONS OF EACH STRIP.CAN YOU CUT PIECES OF ANY SIZE. THANKS
5" max. height. Sold in 20' rolls. You can cut to desired length, and depth depends on how the product is mounted.
Date published: 2015-09-23
What tools are needed to cut this product for a custum fit?
You can cut it with a standard hacksaw.
Date published: 2015-09-23