Attwood Stainless-Steel Neat Cleat, 4-1/2"L
Item No. 314629
Images
Details
https://www.overtons.com/attwood-stainless-steel-neat-cleat-4-12l-314629.html
Attwood Stainless-Steel Neat Cleat, 4-1/2"L
Attwood Stainless-Steel Neat Cleat, 4-1/2"L is rated
out of
5 by
12.
Item No. 314629
$42.99
$59.99
Additional Information
Offering superior strength, sharp looks, and corrosion resistance, this retractable cleat with thin profile installs easily on narrow gunwales. Friction springs reduce rattling and hold cleat up at any position. Drainage receptacles capture moisture. Each stanchion is a 7/8" rod of solid stainless steel. The cleat rises above the deck to 1-5/8" and lowers to 1/2". Measures 4-1/2"L x 1-5/16"W. Requires two 1" dia. holes for installation.
Show moreShow less
| Length (in.) | 4.5 in |
|---|---|
| Quantity | 1 |
| Recommended Use | Boating | Unit Weight | 1.46 lb |
Attwood Stainless-Steel Neat Cleat, 4-1/2"L is rated
out of
5 by
12.
Rated 5 out of
5
by
Eli fishing enthusiast from
neat cleat
I needed a cleat to anchor my new boat. I am pleased with the quality of this cleat that is well made but also is out of the way when not in use. The service was very good and quick. Easy to install. I am also pleased to see that it is made in America .
Date published: 2013-06-26
Rated 5 out of
5
by
L J from
I WOULD DEFINENTLY BUY AGAIN.
THEY ARE TOP QUALITY.I USE THEM TO TIE BOAT TO A DOCK,AND TO HANG MINNOW BUCKET OVER THE SIDE OF BOAT IN THE WATER.WHEN NOT IN USE, JUST PUSH THEM DOWN OUT OF THE WAY.
Date published: 2013-06-13
Rated 5 out of
5
by
john from
Solid product
Installation is a little intimidating because you are drilling holes in your boat. Take your time, its easy. They look fantastic once they're in. Consider making a gasket out of bicycle innertubes to improve the seal against the hull and protect the gel coat.
Date published: 2013-03-18
Rated 5 out of
5
by
Boat Man from
Very nice product
This pull up cleat is great you can step on it and foot will get cauth or hang up on it.
Date published: 2013-03-01
Rated 5 out of
5
by
Tomahawk from
Form AND Function
If you are going to use cleat for tie up, a backing plate of aluminum or poly is essential. If using for fenders, the washers included are fine.
Date published: 2012-12-05
Rated 5 out of
5
by
mussentouchit from
Nice Cleats!
Very attractive and able to keep toes from getting stubbed in areas where a standard cleat would catch feet and shoes.
Date published: 2011-11-28
Rated 5 out of
5
by
Ryan from
Very nice!
Very nice product, installs easy, looks great!
Date published: 2011-09-01
Rated 5 out of
5
by
chip from
great cleat. would buy it again
installed on my boat
Date published: 2010-05-19
What size are the holes that have to be drilled ?
The posts are actually 7/16" in diameter and they require a 7/8" diameter hole. Installation are provided in pdf format at the link below. http://www.attwoodmarine.com/store/product/neat-cleat
Date published: 2015-09-23
Does this include a backing plate?
No a backing plate is not required.
Date published: 2015-09-23